A Step-by-Step Guide to Installing a Bath Tub
A Step-by-Step Guide to Installing a Bath Tub
Blog Article
The writer is making a few good points regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in the article on the next paragraphs.
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably hard project. If the old tub is easily accessible, the project can move quickly; if you need to open up a wall surface to get rid of the old tub and position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have certified on your own for the work as well as are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually currently purchased a new bathtub and also don't need to change the setup of your previous water system pipes.
Your tools and also product checklist should consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic as a result of the restricted accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in area between the tap and the sink. Secure the tap in place with the producer supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Using the two wooden boards under its feet, put the bath tub in the needed setting. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also readjusting the feet on the tub until the level checks out level.
To install faucets, fit the bottom of the furthest adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water system and inspect all joints as well as new pipework for leakages and tighten them if essential. Load the tub and additionally examine the overflow outlet and the regular outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling and securing around the tub ought to wait till the tub has been made use of a minimum of once as this will certainly settle it into its last position.
Planning for the Installment
First of all, the supporting structure supplied with the bathroom must be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its last position.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes as well as cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealer can crack fairly early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that page about How to Install a Bathtub while scouting around the web. In case you liked our blog entry if you please do not forget to share it. Thank-you for going through it.
See Availability
Report this page